EN 10088-2 x5crni18-10 Grade 1.4301 Chemical Composition

EN 10088-2: 2005 Stainless steels. Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes

En 10088-2 Equivalent Grade

This European Standard specifies the technical delivery conditions for hot or cold rolled sheet/plate and strip of standard grades and special grades of corrosion resisting stainless steels for general purposes.

BS EN 10088-2 Chemical Composition.

Designation		Chemical composition % by mass max unless stated
Steel name	Steel number	C	Si	Mn	P	S	N	Cr	Mo	Ni	Others
Ferritic stainless steels – standard grades
X2CrNi12	1.4003	0.030	1.00	1.50	0.040	0.015	0.030	10.5/12.5	–	0.30/1.00	–
X2CrTi12	1.4512	0.030	1.00	1.00	0.040	0.015	–	10.5/12.5	–	–	Ti: 6(C+N)/0.65
X6CrNiTi12	1.4516	0.08	0.70	1.50	0.040	0.015	–	10.5/12.5	–	0.50/1.50	Ti: 0.05/0.35
X6Cr13	1.4000	0.08	1.00	1.00	0.040	0.015	–	12.0/14.0	–	–	–
X6CrAl13	1.4002	0.08	1.00	1.00	0.040	0.015	–	12.0/14.0	–	–	Al: 0.10/0.30
X6Cr17	1.4016	0.08	1.00	1.00	0.040	0.015	–	16.0/18.0	–	–	–
X3CrTi17	1.4510	0.05	1.00	1.00	0.040	0.015	–	16.0/18.0	–	–	Ti: 4(C+N)+0.15/0.80
X3CrNb17	1.4511	0.05	1.00	1.00	0.040	0.015	–	16.0/18.0	–	–	Nb :12C/1.00
X6CrMo17-1	1.4113	0.08	1.00	1.00	0.040	0.015	–	16.0/18.0	0.90/1.40	–	–
X2CrMoTi18-2	1.4521	0.025	1.00	1.00	0.040	0.015	0.030	17.0/20.0	1.80/2.50	–	Ti: 4(C+N)+0.15/0.80
Ferritic stainless steels – special grades
X2CrMnNiTi12	1.4600	0.03	1.00	1.00/2.50	0.040	0.015	0.025	11.0/13.0	–	0.30/1.00	Ti: 6C/0.35
X2CrSiTi15	1.4630	0.030	0.20/1.50	1.00	0.050	0.050	–	13.0/16.0	0.50	0.50	Ti: [4(C+N)+0.15]/0.80
X2CrTi17	1.4520	0.025	0.50	0.50	0.040	0.015	0.015	16.0/18.0	–	–	Ti: 0.30/0.6
X1CrNb15	1.4595	0.020	1.00	1.00	0.025	0.015	0.020	14.0/16.0	–	0.20/0.60	–
X2CrMoTi17-1	1.4513	0.025	1.00	1.00	0.040	0.015	0.015	16.0/18.0	0.80/1.40	–	Ti: 0.30/0.60
X6CrNi17-1	1.4017	0.08	1.00	1.00	0.040	0.015	–	16.0/18.0	–	1.20/1.60	–
X5CrNiMoTi15-2	1.4589	0.08	1.00	1.00	0.040	0.015	–	13.5/15.5	0.20/1.20	1.00/2.50	Ti: 0.30/0.50
X6CrMoNb17-1	1.4526	0.08	1.00	1.00	0.040	0.015	0.040	16.0/18.0	0.80/1.40	–	Nb:7(C+N)+0.10/1.00
X2CrNbZr17	1.4590	0.030	1.00	1.00	0.040	0.015	–	16.0/17.5	–	–	Zr: >7(C+N)+0.15 Nb: 0.35/0.55
X2CrTiNb18	1.4509	0.030	1.00	1.00	0.040	0.015	–	17.5/18.5	–	–	Ti: 0.10/0.60 Nb: 3C+0.30/1.00
X2CrAlSiNb18	1.4634	0.030	0.20/1.50	1.00	0.050	0.050	–	17.5/18.5	0.50	0.50	Nb: 3C+0.30/1.00Al: 0.20/1.50Cu: 0.50
X2CrNbTi20	1.4607	0.030	1.00	1.00	0.040	0.015	0.030	18.5/20.5	–	–	Ti:4 × (C+N) + 0.15/0.80Nb: 1.00
X2CrTi21	1.4611	0.030	1.00	1.00	0.050	0.050	–	19.0/22.0	0.50	0.50	Ti: 4 × (C+N) + 0.20/1.00Cu: 0.50Al: 0.05
X2CrNbCu21	1.4621	0.030	1.00	1.00	0.040	0.015		20.0/21.5	–
X2CrTi24	1.4613	0.030	1.00	1.00	0.050	0.050	–	22.0/25.0	0.50	0.50	Ti: 4 × (C+N) + 0.20/1.00Cu: 0.50Al: 0.05
X2CrMoTi29-4	1.4592	0.025	1.00	1.00	0.030	0.010	0.045	28.0/30.0	3.50/4.50	–	Ti: 4(C+N)+0.15/0.80
Martensitic stainless steels – standard grades
X12Cr13	1.4006	0.08/0.15	1.00	1.50	0.040	0.015	–	11.5/13.5	–	0.75	–
X15Cr13	1.4024	0.12/0.17	1.00	1.00	0.040	0.015	–	12.0/14.0	–	–	–
X20Cr13	1.4021	0.16/0.25	1.00	1.50	0.040	0.015	–	12.0/14.0	–	–	–
X30Cr13	1.4028	0.26/0.35	1.00	1.50	0.040	0.015	–	12.0/14.0	–	–	–
X39Cr13	1.4031	0.36/0.42	1.00	1.00	0.040	0.015	–	12.5/14.5	–	–	–
X46Cr13	1.4034	0.43/0.50	1.00	1.00	0.040	0.015	–	12.5/14.5	–	–	–
X38CrMo14	1.4419	0.36/0.42	1.00	1.00	0.040	0.015	–	13.0/14.5	0.60/1.00	–	–
X55CrMo14	1.4110	0.48/0.60	1.00	1.00	0.040	0.015	–	13.0/15.0	0.50/0.80	–	V: 0.15
X50CrMoV15	1.4116	0.45/0.55	1.00	1.00	0.040	0.015	–	14.0/15.0	0.50/0.80	–	V: 0.10/0.20
X39CrMo17-1	1.4122	0.33/0.45	1.00	1.50	0.040	0.015	–	15.5/17.5	0.80/1.30	1.00	–
X3CrNiMo13-4	1.4313	0.05	0.70	1.50	0.040	0.015	>0.020	12.0/14.0	0.30/0.70	3.5/4.5
X4CrNiMo16-5-1	1.4418	0.06	0.70	1.50	0.040	0.015	>0.020	15.0/17.0	0.80/1.50	4.0/6.0
Martensitic and precipitation-hardening steels – special grades
X1CrNiMoCu12-5-2	1.4422	0.020	0.50	2.00	0.040	0.003	0.020	11.0/13.0	1.30/1.80	4.0/5.0	Cu 0.20/0.80
X1CrNiMoCu12-7-3	1.4423	0.020	0.50	2.00	0.040	0.003	0.020	11.0/13.0	2.30/2.80	6.0/7.0	Cu 0.20/0.80
X5CrNiCuNb16-4	1.4542	0.07	0.70	1.50	0.040	0.015	–	15.0/17.0	0.60	3.0/5.0	Cu 3.0/5.0 Nb 5C/0.45
X7CrNiAl17-7	1.4568	0.09	0.70	1.00	0.040	0.015	–	16.0/18.0	–	6.5/7.8	Al: 0.70/1.50
Austenitic stainless steels – standard grades
X10CrNi18-8	1.4310	0.05/0.15	2.00	2.00	0.045	0.015	0.11	16.0/19.0	0.80	6.0/9.5	–
X2CrNiN18-7	1.4318	0.030	1.00	2.00	0.045	0.015	0.10/0.20	16.5/18.5	–	6.0/8.0	–
X2CrNi18-9	1.4307	0.030	1.00	2.00	0.045	0.015	0.11	17.5/19.5	–	8.0/10.5	–
X2CrNi19-11	1.4306	0.030	1.00	2.00	0.045	0.015	0.11	18.0/20.0	–	10.0/12.0	–
X2CrNiN18-10	1.4311	0.030	1.00	2.00	0.045	0.015	0.12/0.22	17.5/19.5	–	8.5/11.5	–
X5CrNi18-10	1.4301	0.07	1.00	2.00	0.045	0.015	0.11	17.5/19.5	–	8.0/10.5	–
X8CrNiS18-9	1.4305	0.10	1.00	2.00	0.045	0.15/0.35	0.11	17.0/19.0	–	8.0/10.0	Cu: 1.00
X6CrNiTi18-10	1.4541	0.08	1.00	2.00	0.045	0.015	–	17.0/19.0	–	9.0/12.0	Ti: 5C/0.70
X4CrNi18-12	1.4303	0.06	1.00	2.00	0.045	0.015	0.11	17.0/19.0	–	11.0/13.0	–
X2CrNiMo17-12-2	1.4404	0.030	1.00	2.00	0.045	0.015	0.11	16.5/18.5	2.00/2.50	10.0/13.0	–
X2CrNiMoN17-11-2	1.4406	0.030	1.00	2.00	0.045	0.015	0.12/0.22	16.5/18.5	2.00/2.50	10.0/12.0	–
X5CrNiMo17-12-2	1.4401	0.07	1.00	2.00	0.045	0.015	0.11	16.5/18.5	2.00/2.50	10.0/13.0	–
X6CrNiMoTi17-12-2	1.4571	0.08	1.00	2.00	0.045	0.015	–	16.5/18.5	2.00/2.50	10.5/13.5	Ti: 5C/0.70
X2CrNiMo17-12-3	1.4432	0.030	1.00	2.00	0.045	0.015	0.11	16.5/18.5	2.50/3.00	10.5/13.0	–
X2CrNiMo18-14-3	1.4435	0.030	1.00	2.00	0.045	0.015	0.11	17.0/19.0	2.50/3.00	12.5/15.0	–
X2CrNiMoN17-13-5	1.4439	0.030	1.00	2.00	0.045	0.015	0.12/0.22	16.5/18.5	4.0/5.0	12.5/14.5	–
X1NiCrMoCu25-20-5	1.4539	0.020	0.70	2.00	0.030	0.010	0.15	19.0/21.0	4.0/5.0	24.0/26.0	Cu: 1.20/2.00
Austenitic stainless steels – special grades
X5CrNi17-7	1.4319	0.07	1.00	2.00	0.045	0.030	0.11	16.0/18.0	–	6.0/8.0	–
X5CrNiN19-9	1.4315	0.06	1.00	2.00	0.045	0.015	0.12/0.22	18.0/20.0	–	8.0/11.0	–
X5CrNiCu19-6-2	1.4640	0.030/0.08	0.50	1.50/4.0	0.045	0.015	0.03/0.11	18.0/19.0	–	5.5/6.9	Cu: 1.30/2.00
X1CrNi25-21	1.4335	0.020	0.25	2.00	0.025	0.010	0.11	24.0/26.0	0.20	20.0/22.0	–
X6CrNiNb18-10	1.4550	0.08	1.00	2.00	0.045	0.015	–	17.0/19.0	–	9.0/12.0	Nb: 10xC/1.00
X1CrNiMoN25-22-2	1.4466	0.020	0.70	2.00	0.025	0.010	0.10/0.16	24.0/26.0	2.00/2.50	21.0/23.0	–
X6CrNiMoNb17-12-2	1.4580	0.08	1.00	2.00	0.045	0.015	–	16.5/18.5	2.00/2.50	10.5/13.5	Nb: 10xC/1.00
X2CrNiMoN17-3-3	1.4429	0.030	1.00	2.00	0.045	0.015	0.12/0.22	16.5/18.5	2.50/3.00	11.0/14.0	–
X3CrNiMo17-13-3	1.4436	0.05	1.00	2.00	0.045	0.015	0.11	16.5/18.5	2.50/3.00	10.5/13.0	–
X2CrNiMoN18-12-4	1.4434	0.030	1.00	2.00	0.045	0.015	0.10/0.20	16.5/19.5	3.0/4.0	10.5/14.0	–
X2CrNiMo18-15-4	1.4438	0.030	1.00	2.00	0.045	0.015	0.11	17.5/19.5	3.0/4.0	13.0/16.0	–
X1CrNiMoCuN24-22-8	1.4652	0.020	0.50	2.00/4.0	0.030	0.005	0.45/0.55	23.0/25.0	7.0/8.0	21.0/23.0	Cu: 0.30/0.60
X1CrNiSi18-15-4	1.4361	0.015	3.7/4.5	2.00	0.025	0.010	0.11	16.5/18.5	0.20	14.0/16.0	–
X6CrMnNiCuN18-12-4-2	1.4646	0.02/0.10	1.00	10.5/12.5	0.050	0.015	0.20/0.30	17.0/19.0	–	3.5/4.5	Cu: 1.50/3.00
X11CrNiMnN19-8-6	1.4369	0.07/0.15	0.50/1.00	5.0/7.5	0.030	0.015	0.20/0.30	17.5/19.5	–	6.5/8.5	–
X8CrMnNi19-6-3	1.4376	0.10	1.00	5.0/8.0	0.045	0.015	0.30	17.0/20.5	–	2.00/4.5	–
X12CrMnNiN17-7-5	1.4372	0.15	1.00	5.5/7.5	0.045	0.015	0.05/0.25	16.0/18.0	–	3.5/5.5	–
X2CrMnNiN17-7-5	1.4371	0.030	1.00	6.0/8.0	0.045	0.015	0.15/0.20	16.0/17.0	–	3.5/5.5	–
X9CrMnNiCu17-8-5-2	1.4618	0.10	1.00	5.5/9.5	0.070	0.010	0.15	16.5/18.5	–	4.5/5.5	Cu: 1.50/2.50
X12CrMnNiN18-9-5	1.4373	0.15	1.00	7.5/10.5	0.045	0.015	0.05/0.25	17.0/19.0	–	4.0/6.0	–
X9CrMnCuNB17-8-3	1.4597	0.10	2.00	6.5/8.5	0.040	0.030	0.15/0.30	16.0/18.0	1.00	2.00	B:0.0005/0.0050 Cu: 2.00/3.5
X1NiCrMo31-27-4	1.4563	0.020	0.70	2.00	0.030	0.010	0.11	26.0/28.0	3.0/4.0	30.0/32.0	Cu: 0.70/1.50
X1CrNiMoCuN25-25-5	1.4537	0.020	0.70	2.00	0.030	0.010	0.17/0.25	24.0/26.0	4.7/5.7	24.0/27.0	Cu: 1.00/2.00
X1CrNiMoCuN20-18-7	1.4547	0.020	0.70	1.00	0.030	0.010	0.18/0.25	19.5/20.5	6.0/7.0	17.5/18.5	Cu: 0.50/1.00
X1CrNiMoCuNW24-22-6	1.4659	0.020	0.70	2.00/4.0	0.030	0.010	0.35/0.50	23.0/25.0	5.5/6.5	21.0/23.0	Cu: 1.00/2.00 W: 1.50/2.50
X1NiCrMoCuN25-20-7	1.4529	0.020	0.50	1.00	0.030	0.010	0.15/0.25	19.0/21.0	6.0/7.0	24.0/26.0	Cu: 0.50/1.50
X2CrNiMnMoN25-18-6-5	1.4565	0.030	1.00	5.0/7.0	0.030	0.015	0.30/0.60	24.0/26.0	4.0/5.0	16.0/19.0	Nb: 0.15
Austenitic-ferritic stainless steels-standard grades
X2CrNiN23-4	1.4362	0.030	1.00	2.00	0.035	0.015	0.05/0.20	22.0/24.0	0.10/0.60	3.5/5.5	Cu 0.10/0.60
X2CrNiMoN22-5-3	1.4462	0.030	1.00	2.00	0.035	0.015	0.10/0.22	21.0/23.0	2.50/3.50	4.5/6.5	–
Austenitic-ferritic stainless steels-special grades
X2CrNiN22-2	1.4062	0.030	1.00	2.00	0.040	0.010	0.16/0.28	21.5/24.0	0.45	1.00/2.90	–
X2CrNiCuN23-4	1.4655	0.030	1.00	2.00	0.035	0.015	0.05/0.20	22.0/24.0	0.10/0.60	3.5/5.5	Cu: 1.00/3.00
X2CrMnNiN21-5-1	1.4162	0.040	1.00	4.0/6.0	0.040	0.015	0.20/0.25	21.0/22.0	0.10/0.80	1.35/1.90	Cu: 0.10/0.80
X2CrMnNiMoN21-5-3	1.4482	0.030	1.00	4.0/6.0	0.035	0.030	0.05/0.20	19.5/21.5	0.10/0.60	1.50/3.50	Cu: 1.00
X2CrNiMnMoCuN24-4-3-2	1.4662	0.030	0.70	2.50/4.0	0.035	0.005	0.20/0.30	23.0/25.0	1.00/2.00	3.0/4.5	Cu; 0.10/0.80
X2CrNiMoN29-7-2	1.4477	0.030	0.50	0.80/1.50	0.030	0.015	0.30/0.40	28.0/30.0	1.50/2.60	5.8/7.5	Cu: 0.80
X2CrNiMoCuN25-6-3	1.4507	0.030	0.70	2.00	0.035	0.015	0.20/0.30	24.0/26.0	3.0/4.0	6.0/8.0	Cu: 1.00/2.50
X2CrNiMoN25-7-4	1.4410	0.030	1.00	2.00	0.035	0.015	0.24/0.35	24.0/26.0	3.0/4.5	6.0/8.0	–
X2CrNiMoCuWN25-7-4	1.4501	0.030	1.00	1.00	0.035	0.015	0.20/0.30	24.0/26.0	3.0/4.0	6.0/8.0	Cu: 0.50/1.00 W: 0.50/1.00
X2CrNiMoSi18-5-3	1.4424	0.030	1.40/2.00	1.20/2.00	0.035	0.015	0.05/0.10	18.0/19.0	2.50/3.0	4.5/5.2	–

BS EN 10088-2 mechanical properties – austenitic stainless steels

Designation		Mechanical properties min unless stated
Steel name	Steel number	Product		Proof strength		Tensile strength R_m N/mm²	Elongation^5),6) %
Steel name	Steel number	Form²⁾	Max thickness mm	R_p0.2^3),4) N/mm²	R_p1.0^3),4) N/mm²	Tensile strength R_m N/mm²	Elongation^5),6) %
Austenitic stainless steels in the solution annealed condition¹⁾ – standard grades
X10CrNi18-8	1.4310	C	8	250	280	600/950	40
X2CrNiN18-7	1.4318	C	8	350	380	650/850	40
		H	13.5	330	370	650/850	40
		P	75	330	370	630/830	45
X2CrNi18-9	1.4307	C	8	220	250	520/700	45
		H	13.5	200	240	520/700	45
		P	75	200	240	500/700	45
X2CrNi19-11	1.4306	C	8	220	250	520/700	45
		H	13.5	200	240	520/700	45
		P	75	200	240	500/700	45
X2CrNiN18-10	1.4311	C	8	290	320	550/750	40
		H	13.5	270	310	550/750	40
		P	75	270	310	550/750	40
X5CrNi18-10	1.4301	C	8	230	260	540/750	45
		H	13.5	210	250	520/720	45
		P	75	210	250	520/720	45
X8CrNiS18-9	1.4305	P	75	190	230	500/700	35
X6CrNiTi18-10	1.4541	C	8	220	250	520/720	40
		H	13.5	200	240	520/720	40
		P	75	200	240	500/700	40
X4CrNi18-12	1.4303	C	8	220	250	500/650	45
X2CrNiMo17-12-2	1.4404	C	8	240	270	530/680	40
		H	13.5	220	260	530/680	40
		P	75	220	260	520/670	45
X2CrNiMoN17-11-2	1.4406	C	8	300	330	580/780	40
		H	13.5	280	320	580/780	40
		P	75	280	320	580/780	40
X5CrNiMo17-12-2	1.4401	C	8	240	270	530/680	40
		H	13.5	220	260	530/680	40
		P	75	220	260	520/670	45
X6CrNiMoTi17-12-2	1.4571	C	8	240	270	540/690	40
		H	13.5	220	260	540/690	40
		P	75	220	260	520/670	40
X2CrNiMo17-12-3	1.4432	C	8	240	270	550/700	40
		H	13.5	220	260	550/700	40
		P	75	220	260	520/670	45
X2CrNiMo18-14-3	1.4435	C	8	240	270	550/700	40
		H	13.5	220	260	550/700	40
		P	75	220	260	520/670	45
X2CrNiMoN17-13-5	1.4439	C	8	290	320	580/780	35
		H	13.5	270	310	580/780	35
		P	75	270	310	580/780	40
X1NiCrMoCu25-20-5	1.4539	C	8	240	270	530/730	35
		H	13.5	220	260	530/730	35
		P	75	220	260	520/720	35
Austenitic stainless steels in the solution annealed condition¹⁾ – special grades
X5CrNi17-7	1.4319	C	3	230	260	550/750	45
X5CrNi17-7	1.4319	H	6	230	260	550/750	45
X5CrNiN19-9	1.4315	C	8	290	330	500/720	40
		H	13.5	270	310	500/750	40
		P	75	270	310	500/750	40
X5CrNiCu19-6-2	1.4640	C	8	230	260	540/750	45
X5CrNiCu19-6-2	1.4640	H	13.5	210	240	520/720	45
X1CrNi25-21	1.4335	P	75	200	240	470/670	40
X6CrNiNb18-10	1.4550	C	8	220	250	520/720	40
		H	13.5	200	240	520/720	40
		P	75	200	240	500/700	40
X1CrNiMn25-22-2	1.4466	P	75	250	290	540/740	40
X6CrNiMoN17-13-2	1.4580	P	75	220	260	520/720	40
X2CrNiMoN17-13-3	1.4429	C	8	300	330	580/780	35
		H	13.5	280	320	580/780	35
		P	75	280	320	580/780	40
X3CrNiMo17-13-3	1.4436	C	8	240	270	550/700	40
		H	13.5	220	260	550/700	40
		P	75	220	260	530/730	40
X2CrNiMoN18-12-4	1.4434	C	8	290	320	570/770	35
		H	13.5	270	310	570/770	35
		P	75	270	310	540/740	40
X2CrNiMo18-15-4	1.4438	C	8	240	270	550/700	35
		H	13.5	220	260	550/700	35
		P	75	220	260	520/720	40
X1CrNiMoCuN24-22-8	1.4652	C	8	430	470	750/1000	40
		H	13.5	430	470	750/1000	40
		P	75	430	470	750/1000	40
X1CrNiSi18-15-4	1.4361	P	75	220	260	530/730	40
X11CrNiMnN19-8-6	1.4369	C	4	340	370	750/950	35
X6CrMnNiCuN18-12-4-2	1.4646	C	8	380	400	650/850	30
X12CrMnNiN17-7-5	1.4372	C	8	350	380	680/780	45
		H	13.5	330	370	680/880	40
		P	75	330	370	750/950	40
X2CrMnNiN17-7-5	1.4371	C	8	300	330	650/850	45
		H	13.5	280	320	650/850	45
		P	75	280	320	630/830	35
X9CrMnNiCu17-8-5-2	1.4618	C	8	230	250	540/850	45
		H	13.5	230	250	520/830	45
		P	75	210	240	520/830	45
X12CrMnNiN18-9-5	1.4373	C	8	340	370	680/880	45
		H	13.5	320	360	680/880	45
		P	75	320	360	600/800	35
X8CrMnCuNB17-8-3	1.4597	C	8	300	330	580/780	40
X8CrMnCuNB17-8-3	1.4597	H	13.5	300	330	580/780	40
X8CrMnNi19-6-3	1.4376	C	4	400	420	600/900	40
X8CrMnNi19-6-3	1.4376	H	13.5	400	420	600/900	40
X1NiCrMoCu31-27-4	1.4563	P	75	220	260	500/700	40
X1CrNiMoCuN25-25-5	1.4537	P	75	290	330	600/800	40
X1CrNiMoCuN20-18-7	1.4547	C	8	320	350	650/850	35
		H	13.5	300	340	650/850	35
		P	75	300	340	650/850	40
X1CrNiMoCuNW24-22-6	1.4659	P	75	420	460	800/1000	40
X1NiCrMoCuN25-20-7	1.4529	P	75	300	340	650/850	40
X2CrNiMnMoN25-18-6-5	1.4565	C	8	420	460	800/950	30
		H	10	420	460	800/950	30
		P	40	420	460	800/950	30

Note

The solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained.
C= Cold rolled strip; H= hot rolled strip; P= hot rolled plate.
If, in the case of strip in rolling widths<300mm, longitudinal test pieces are taken, the minimum values are reduced as follow:
1. proof strength: minus 15N/mm²
2. elongation for constant gauge length: minus 5%
3. elongation for proportional gauge length: minus 2%
For continuously hot rolled products, 20N/mm² higher minimum values of R_p0.2 and 10N/mm²higher minimum values of R_p1.0 may be agreed at the time of enquiry and order.
The values apply for test pieces with a gauge length of 80mm and a width of 20mm. Test pieces with a gauge length of 50mm and a width of 12.5mm can also be used.
The values apply for test pieces with a gauge length of 5.65 S_o^0.5

BS EN 10088-2 mechanical properties – ferritic stainless steels

Designation		Mechanical properties min unless stated
Steel name	Steel number	Product		Proof strength R_p0.2 N/mm²		Tensile strength R_m N/mm²	Elongation A_80mm²⁾ for < 3mm A³⁾ for > 3mm
Steel name	Steel number	Form¹⁾	Max thickness mm	Longitudinal	Transverse	Tensile strength R_m N/mm²	%
Ferritic stainless steels at room temperatures in the annealed condition- standard grades
X2CrNi12	1.4003	C	8	280	320	450/650	20
		H	13.5	280	320	450/650	20
		P	25⁴⁾	250	280	450/650	18
X2CrTi12	1.4512	C	8	210	220	380/560	25
X2CrTi12	1.4512	H	13.5	210	220	380/560	25
X6CrNiTi12	1.4516	C	8	280	320	450/650	23
		H	13.5	280	320	450/650	23
		P	25⁴⁾	250	280	450/650	20
X6Cr13	1.4000	C	8	240	250	400/600	19
		H	13.5	220	230	400/600	19
		P	25⁴⁾	220	230	400/600	19
X6CrAl13	1.4002	C	8	230	250	400/600	17
		H	13.5	210	230	400/600	17
		P	25⁴⁾	210	230	400/600	17
X6Cr17	1.4016	C	8	260	280	450/600	20
		H	13.5	240	260	450/600	18
		P	25⁴⁾	240	260	430/630	20
X3CrTi17	1.4510	C	8	230	240	420/600	23
X3CrTi17	1.4510	H	13.5	230	240	420/600	23
X3CrNb17	1.4511	C	8	230	240	420/600	23
X6CrMo17-1	1.4113	C	8	260	280	450/630	18
X6CrMo17-1	1.4113	H	13.5	260	280	450/630	18
X2CrMoTi18-2	1.4521	C	8	300	320	420/640	20
		H	13.5	280	300	400/600	20
		P	12	280	300	420/620	20
Ferritic stainless steels at room temperatures in the annealed condition- special grades
X2CrMnNiTi12	1.4600	H	10	–	375	500/650	20
X2CrSiTi15	1.4630	C	8	210	230	380/580	20
X2CrTi17	1.4520	C	8	180	200	380/530	24
X1CrNb15	1.4595	C	8	210	220	380/560	25
X2CrMoTi17-1	1.4513	C	8	200	220	400/550	23
X6CrNi17-1	1.4017	C	8	330	350	500/750	12
X5CrNiMoTi15-2	1.4589	C	8	400	420	550/750	16
X5CrNiMoTi15-2	1.4589	H	13.5	360	380	550/750	14
X6CrMoNb17-1	1.4526	C	8	280	300	480/560	25
X2CrNbZr17	1.4590	C	8	230	250	400/550	23
X2CrTiNb18	1.4509	C	8	230	250	430/630	18
X2CrAlSiNb18	1.4634	C	8	240	260	430/650	18
X2CrNbTi20	1.4607	C	8	230	250	430/630	18
X2CrTi21	1.4611	C	8	230	250	430/630	18
X2CrTi24	1.4613	C	8	230	250	430/630	18
X2CrMoTi29-4	1.4592	C	8	430	450	550/700	20

Note

C= Cold rolled strip; H= hot rolled strip; P= hot rolled plate.
The values apply for test pieces with a gauge length of 80mm and a width of 20mm. Test pieces with a gauge length of 50mm and a width of 12.5mm can also be used.
The values apply for test pieces with a gauge length of 5.65 S_o^0.5
For thicknesses above 25mm, the mechanical properties can be agreed.

BS EN 10088-2 mechanical properties – martensitic stainless steels

Designation		Mechanical properties min unless stated
Steel name	Steel number	Product		Heat treatment condition²⁾	Proof strength R_p0.2N/mm²	Tensile strength R_mN/mm²	Elongation A_80mm⁴⁾ for < 3mm A⁵⁾ for >3mm	Hardness³⁾
Steel name	Steel number	Form¹⁾	Thickness mm max.	Heat treatment condition²⁾	Proof strength R_p0.2N/mm²	Tensile strength R_mN/mm²	%	HRB	HB	HRC	HV
Martensitic stainless steels in the heat treated condition-standard steels
X12Cr13	1.4006	C	8	A	–	<600	20	90	200	–	–
		H	13.5	A	–	<600	20	90	200	–	–
		P⁶⁾	75	QT550	400	550/750	15	–	–	–	–
		P⁶⁾	75	QT650	450	650/850	12	–	–	–	–
X15Cr13	1.4024	C	8	A	–	<650	20	90	200	–	–
		H	13.5	A	–	<650	20	90	200	–	–
		P	75	A	–	–	–	–	–	–	–
		P	75	QT550	400	550/750	15	–	–	–	–
		P	75	QT650	450	650/850	12	–	–	–	–
X20Cr13	1.4021	C	3	QT	–	–	–	–	–	44/50	440/530
		C	8	A	–	<700	15	95	225	–	–
		H	13.5	A	–	<700	15	95	225	–	–
		P⁶⁾	75	QT650	450	650/850	12	–	–	–	–
		P⁶⁾	75	QT750	550	750/950	10	–	–	–	–
X30Cr13	1.4028	C	3	QT	–	–	–	–	–	45/51	450/550
		C	8	A	–	<740	15	97	235	–	–
		H	13.5	A	–	<740	15	97	235	–	–
		P⁶⁾	75	QT800	600	800/1000	10	–	–	–	–
X39Cr13	1.4031	C	3	QT	–	–	–	–	–	47/53	480/580
		C	8	A	–	<760	12	98	240	–	–
		H	13.5	A	–	<760	12	98	240	–	–
X46Cr13	1.4034	C	3	QT	–	<780				49/55	510/610
		C	8	A	–	<780	12	99	245	–	–
		H	13.5	A	–	<780	12	99	245
X38CrMo14	1.4419	C	3	QT	–	–	–	–	–	46/52	450/560
		C	4	A	–	<760	15	97	235	–	–
		H	6.5	A	–	<760	15	97	235	–	–
X55CrMo14	1.4110	C	8	A	–	<850	12	100	280	–	–
		H	13.5	A	–	<850	12	100	280	–	–
		P	75	A	–	–	–	–	–	–	–
X46CrMoV15	1.4116	C	8	A	–	<850	12	100	280	–	–
X46CrMoV15	1.4116	H	13.5	A	–	<850	12	100	280	–	–
X39CrMo17-1	1.4122	C	3	QT	–	–	–	–	–	47/53	480/580
		C	8	A	–	<900	12	100	280	–	–
		H	13.5	A	–	<900	12	100	280	–	–
X3CrNiMo13-4	1.4313	P	75	QT780	630	780/980	15	–	–	–	–
X3CrNiMo13-4	1.4313	P	75	QT900	800	900/1100	11	–	–	–	–
X4CrNiMo16-5-1	1.4418	P	75	QT840	660	840/1100	14	–	–	–	–
Martensitic stainless steels in the heat treated condition-special steels
X1CrNiMoCu12-5-2	1.4422	H	13.5	A	550	750/950	15	100	300	–	–
X1CrNiMoCu12-5-2	1.4422	P	75	QT650	550	750/950	15	–	–	–	<300
X1CrNiMoCu12-7-3	1.4423	H	13.5	A	550	750/950	15	100	300	–	–
X1CrNiMoCu12-7-3	1.4423	P	75	QT650	550	750/950	15	–	–	–	<300

Note

C= Cold rolled strip; H= hot rolled strip; P= hot rolled plate.
A= annealed, QT= quenched and tempered.
The Brinell or Vickers or Rockwell hardness is normally determined for product forms C and H in heat-treatment condition A. The tensile test shall be carried out in referee testing.
The values apply for test pieces with a gauge length of 80mm and a width of 20mm. Test pieces with a gauge length of 50mm and a width of 12.5mm can also be used.
The values apply for test pieces with a gauge length of 5.65 S_o^0.5
Plates may also be delivered in the annealed condition; in such cases the mechanical properties are to be agreed at the time of enquiry and order.

BS EN 10088-2 mechanical properties – austenitic-ferritic (duplex) stainless steels

Designation		Mechanical properties min unless stated
Steel name	Steel number	Product		Proof strength R_p0.2^2),3) N/mm²	Tensile strength R_m N/mm²	Elongation^4),5) %
Steel name	Steel number	Form¹⁾	Max thickness mm	Proof strength R_p0.2^2),3) N/mm²	Tensile strength R_m N/mm²	Elongation^4),5) %
Austenitic-ferritic stainless steels in the solution annealed condition-standard grades
X2CrNiN23-4	1.4362	C	8	450	650/850	20
		H	13.5	400	650/850	20
		P	75	400	630/800	25
X2CrNiMoN22-5-3	1.4462	C	8	500	700/950	20
		H	13.5	460	700/950	25
		P	75	460	640/840	25
Austenitic-ferritic stainless steels in the solution annealed condition-special grades
X2CrNiN22-2	1.4062	C	6.4	530	700/900	20
		H	10	480	680/900	30
		P	75	450	650/850	30
X2CrNiCuN23-4	1.4655	C	8	420	600/850	20
		H	13.5	400	600/850	20
		P	75	400	630/800	25
X2CrMnNiN21-5-1	1.4162	C	6.4	530	700/900	20
		H	10	480	680/900	30
		P	75	430	650/850	30
X2CrMnNiMoN21-5-3	1.4482	C	6.4	500	700/900	20
		H	10	480	660/900	30
		P	75	450	650/850	30
X2CrNiMnMoCuN24-4-3-2	1.4662	C	6.4	550	750/900	25
		H	13	550	750/900	25
		P	75	480	680/900	25
X2CrNiMoN29-7-2	1.4477	C	8	650	800/1050	20
		H	13.5	550	750/1000	20
		P	75	550	750/1000	20
X2CrNiMoCuN25-6-3	1.4507	C	8	550	750/1000	20
		H	13.5	530	750/1000	20
		P	75	530	730/930	25
X2CrNiMoN25-7-4	1.4410	C	8	550	750/1000	20
		H	13.5	530	750/1000	20
		P	75	530	730/930	20
X2CrNiMoCuWN25-7-4	1.4501	P	75	530	730/930	25
X2CrNiMoSi18-5-3	1.4424	C	8	450	700/900	25
		H	13.5	450	700/900	25
		P	75	400	680/900	25

Note

C= Cold rolled strip; H= hot rolled strip; P= hot rolled plate.
If, in the case of strip in rolling widths < 300mm, longitudinal test pieces are taken, the minimum proof strength values are reduced by 15N/mm²
For continuously hot rolled products, 20N/mm² higher minimum values of R_p0.2 may be agreed at the time of enquiry and order.
The values apply for test pieces with a gauge length of 80mm and a width of 20mm. Test pieces with a gauge length of 50mm and a width of 12.5mm can also be used.
The values apply for test pieces with a gauge length of 5.65 S_o^0.5

EN10088 Stainless Steel

EN 10088-1: 2005 Stainless steels. List of stainless steels
EN 10088-2: 2005 Stainless steels. Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 10088-3: 2005 Stainless steels. Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 10088-4: 2009 Stainless steels. Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes
EN 10088-5: 2009 Stainless steels. Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes